RFRemotech - MB32Q 32 Cue Programmable Fireworks Firing System

Take your fireworks display to the next level using the RFRemotech MB32Q. The MB32Q can be used in simple manual mode, sequence mode, stepper mode and for a fully scripted and programmed pyro musical.

Included with the MB32Q firing system is the MB32Q receiver, black plastic carrying case, antenna, two keys, external battery jumper. No remote or USB cable is included in the base price. Please review remote, USB cable, and battery options before adding a MB32Q to the cart.

MB32Q Key Features:

The MB32Q firing system can be controlled in manual mode with the TCF200-12LN remote, and in program, sequence, and step modes using the TCF200-6XT or the TCF200-U multi-function remote.

The MB32Q firing system cue time sequence can be programmed using the buttons and screen on the MB32Q firing module or using the free show editor and melody software and a USB cord to load a program you create on a windows computer directly into the MB32Q firing module. Go to the RFRemotech website for more information about the scripting software.

Click Here Software Link                           

The MB32Q firing system has advanced cue overload protection with the capability of 10 amps output, and reverse protection to insure the firing system cues are not damaged from shorted wires installed in the cues. If there is a shorted igniter in a cue, the cue will not activate. Other features include a low power alarm and shorted cue warning.

The MB32Q can be powered using high quality AA batteries like Energizer Industrial or Duracell Procell installed behind the module rear battery door. The high quality AA alkaline batteries will ignite two non-pyrogen clip igniters or three e-matches hooked in parallel, or six e-matches in series.

The MB32Q can be powered by a 12 to 24 volt external power source using the external jumper provided. We recommend a power source that's 2ah or larger in capacity. A 12 volt sealed lead acid battery or an 18 volt DeWalt power tool battery are a few examples of batteries that could be used to power the MB32Q. Using the two batteries mentioned above the MB32Q can ignite six clip igniters or six e-matches in parallel, or twelve e-matches in series.

  Manual Transmitter Key Features:

433.92 MHz FSK 200 meter transmitter works with the RFRemotech MS32Q, MB32Q, and MS32Q Pro firing systems.

On/Off power switch

Backlit buttons

Red LED when turned on. Green indicator LED when transmitting.

The transmitter goes to sleep / locks after three minutes with no use to save battery life and for security.

Advanced transmitter technology sending out packets of information when transmitting.

200 meter range. We recommend the MB32Q is used at least eighteen inches off the ground with antenna extended straight up for best results. The transmitter antenna should be extended, at least four feet off the ground, pointed straight up.

Powered by a 12 volt A23 battery under the back cover.

 Program/Stepper Remote Key features:

The 433.92 MHz FSK 200 meter transmitter works with the RFRemotech MS32Q, MB32Q and MS32Q Pro firing systems.

On/Off switch

Back Lit Buttons

Red LED when turned on. Green indicator LED when transmitting.

Lock/Unlock Button; alloys the user to lock and unlock the remote for safety without turning the remote off.

Stop Button; reset the firing module back to the first cue.

Stepper Button; push one button to step through all 32 cue.

Sleep Mode; the back LED light shuts off after three minutes to save battery power. The Unlock button must be pushed before the remote can be used again or the on/off switch is turned off then back on.

Start Button; start a program installed in the MB32Q module.

Pause button; pause a program installed in the MB32Q module.

Continue button; continue an installed program in the MB32Q module.

Why purchase the MB32Q from Remote Firing Systems .com?

The transmitter and receiver are taken apart and inspected for quality.

A conformal coating is applied to all received electronic components for water damage and corrosion protection.

The transmitter and receiver are range tested at 650 feet and load tested for proper operation before shipping to the customer.

Free one year warranty; the manufacture does not provide a warranty.

The MB32Q is not a disposable firing system, it can be returned for repair if a problem does arise.

Warranty:

One year parts defect warranty. Scratches and burns are not covered. Water damage is not covered. Misuse is not covered.

 Installing the MB32Q Driver and Show Editor Software onto a Computer:

First use a USB to USB 2.0 cord to connect the MB32Q USB to a computer USB. Make sure the MB32Q has a power supply, then turn the key to ON.

Next manually install the MB32Q USB driver by clicking on the file named USB Driver.

Download the USB driver zip file located on the bottom half of the RFRemotech MB32Q web page:

https://www.rfremotech.com/MB322BSeries.html

USB Driver link

File name USBDriver

Unzip the file, click on USBDriver, click on the X64 file if you have a 64 bit computer, then click on the file named DPlnst64 to manually load the MB32Q driver.

If you have a 32 bit computer click on the X86 file, then click on DPlnst to manually load the MB32Q driver.

Now that the driver is installed the show editor software can be downloaded and installed

RFRemotech Fireworks Show Editor Software: Show Editor Software link

File name Showeditor_V5.2.5BD.exe

How to use the Show editor  video link 

You can also change the setting of your PC according to the guides below to download the Show Editor Software:

For Windows 8.0:  How to make Window 8 allow the installation of the driver

For Windows 8.1:  How to make Window 8.1 allow the installation of the driver

For Windows 10:   How to make Window 10 allow the installation of the driver